United States Stove Company
  
  home | products | dealers | search | checkout | contact  
 

United States Stove Company FAQ
Search The FAQ:
 

FAQ Index
Categories:
Category: 6033 6035 6037 Multifuel Stove
  1. IS THE AUGER SUPPOSED TO CONTINUOUSLY TURN? OR IS IT SUPPOSED TO TURN ABOUT 3 TIMES STOP THEN ROTATE MORE?
  2. My 6035 corn pellet stove keeps going out after about 30 minutes. Also can the blower be turned up to force more air for circulation.
  3. Having a problem with the auger on the 6035 corn stove. It will not pull the wood pellets through the auger to the agitator. It works for a while then it quits bringing the pellets through. The auger works but there are no pellets. It seems as though it crushes them up and does not push them through.
  4. WE INSTALLED OUR STOVE THIS WEEK AND THE AUGER THAT ROTATES THE CORN ALREADY QUIT WORKING. HOW DO WE GET IT FIXED?
  5. We are having a problem with a dirty sooty stove. Worked great for the first six weeks now it is so sooty that the glass is solid black within a half hour of lighting corn is very dry no other changes made. cindy
  6. Our 6033 ran pretty good for two days. Now it shuts itself down in about 30 min. or we can't even get it to burn at all. We have it vented up from basement floor about 5 feet. Does it need more motor to get the chimminy to work. the first 2 days we had lots of wind here now not so much
  7. Our stove works great on pellets but we get big globbs and lots of half burned ash with corn-- we can't seem to get good results with corn.
  8. What is new and improved on 6037 over the 6033 or 6035?
  9. When I turn my unit off it keeps running and the auger keeps feeding.
  10. Auger came loose, is it broken ?
  11. Green light is flashing and nothing is happening ?
  12. Unit is extremely hot and the green light is flashing, whats wrong ?
  13. Is there a fresh air kit for outside air ?
  14. What kind of pipe do I buy ?
  15. How high should my pipe be ?
  16. What is the clearance to the back wall ?
  17. How long does it take for the auger and agitator to start turning when I first turn the unit on ?
  18. Why will my Disribution/Circulation fan not run during testing phase ?
  19. Why does my unit shut down after only 15 minutes of testing.
  20. How do I reset the control board once the Green light has started flashing ?
  21. When I turn the knob to 1 how long before the unit starts to turn the auger ?
  22. How far open should my slide draft be set ?
  23. How often should I clean out this unit ?
  24. Fire keeps going out for no reason.
  25. What are the slides in the back wall at the bottom for ?
  26. What are the slides in the bottom of the firebox on each side of the burn pot for ?
  27. My fire burns with a lazy Orange Flame, what causes this ?
  28. Where does my unit pull in air from ?
  29. My stove will not shut down properly no matter what I do, I have to unplug it to shutdown. Any suggestions?
  30. I have a model 6037, and the auger doesn't work all the time.
  31. I have a 6037 stove, the glass gets completely covered with soot within an hour of running, and I can't keep the stove running on settings #1 and #2, I burn good Iowa corn, 14%. My father-in-law doesn't have these problems with his 6035. Can I adjust the damper with the 6037 to keep my glass cleaner? Do you have a field technician in Iowa, I would like to have him look at my 6037, to be honest I wasn't too happy with in last year.



  1. IS THE AUGER SUPPOSED TO CONTINUOUSLY TURN? OR IS IT SUPPOSED TO TURN ABOUT 3 TIMES STOP THEN ROTATE MORE?
    Depending on the setting the Auger will turn for: on for 3.4 seconds then shut off for 16.6 seconds. Setting 1 on for 4.1 seconds then shut off for 15.9 seconds. Setting 2 on for 5.3 seconds then shut off for 14.7 seconds. on Setting 3 on for 7.7 seconds then shut off for 12.3 seconds. Setting 4 on for 10.5 seconds then shut off for 9.5 seconds on high.
    945 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  2. My 6035 corn pellet stove keeps going out after about 30 minutes. Also can the blower be turned up to force more air for circulation.
    This unit is controlled by a forced air exhaust system , however if your exhaust slide is in too far it will cause the unit to burn out from lack of oxygen. Re-adjust your slide to allow for more air. The circulation blower will stay at a constant speed.
    921 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  3. Having a problem with the auger on the 6035 corn stove. It will not pull the wood pellets through the auger to the agitator. It works for a while then it quits bringing the pellets through. The auger works but there are no pellets. It seems as though it crushes them up and does not push them through.
    We do have a new polished Auger that seems to work better than the old style that you have.
    755 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  4. WE INSTALLED OUR STOVE THIS WEEK AND THE AUGER THAT ROTATES THE CORN ALREADY QUIT WORKING. HOW DO WE GET IT FIXED?
    Check to make sure the Auger has not slipped out of its track, if you will twist the auger Counter-Clockwise to see if it turns freely. If so it has slipped out.
    787 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  5. We are having a problem with a dirty sooty stove. Worked great for the first six weeks now it is so sooty that the glass is solid black within a half hour of lighting corn is very dry no other changes made. cindy
    There are several things that can cause the unit to soot up the glass. 1) Air shutter not openned far enough. 2) the corn moisture content too high. 3) Chimney clogging up from soot. 4) Air ports above the brick in firebox clogging from soot. If you will turn your unit up on high every few hours and let it burn off the soot that will help.
    648 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  6. Our 6033 ran pretty good for two days. Now it shuts itself down in about 30 min. or we can't even get it to burn at all. We have it vented up from basement floor about 5 feet. Does it need more motor to get the chimminy to work. the first 2 days we had lots of wind here now not so much
    NO. The motor should be more than strong enough to blow the exhaust out 5 feet. Look in the unit above the brick on the inside of the firebox. Make sure that the holes for the draft are not clogged. Also make sure the air shutter is open and not closed.
    706 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  7. Our stove works great on pellets but we get big globbs and lots of half burned ash with corn-- we can't seem to get good results with corn.
    You will need to add a substance called Oyster Shell for the breakdown of the build up of clinkers on your agitator.
    828 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  8. What is new and improved on 6037 over the 6033 or 6035?
    The 6037 has a new Circuit board for constant delivery of air,new auger from 2" cast to 1 1/2 " steel,and a new safety cage for hopper.
    619 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  9. When I turn my unit off it keeps running and the auger keeps feeding.
    For safety reasons the stove will continue to run at a much lower heat setting for 10 minutes. After 10 Minutes, the auger will slow down further and continue until the " LOW LIMIT SAFETY" sensor tells the control board it is safe to shutdown.
    756 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  10. Auger came loose, is it broken ?
    NO, the auger sits in a "T" slot groove in the back of the shaft and may have slid forward just enough to come out of that slot. If you turn the auger in a circular motion while pushing it back in you will feel it slide into that "T" slot coupler, you will not be able to turn the auger by hand anymore.
    722 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  11. Green light is flashing and nothing is happening ?
    Turn the stove completely off and then back on to reset the board. Begin the Start-Up Procedure.
    708 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  12. Unit is extremely hot and the green light is flashing, whats wrong ?
    Your Hi Limit Safety Sensor is the cause of the green light flashing. This is due to the fact if the unit gets too hot the safety switch will shut the unit down. Let the unit cool and then restart.
    653 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  13. Is there a fresh air kit for outside air ?
    Yes part # 67FAK. This allows combustion air to enter the firepot from outside. This will increase the efficiency and reduce the likelihood of creating negative pressure or vacuum effect in your home.
    780 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  14. What kind of pipe do I buy ?
    You will need 3" PL type pipe . If you go over 4 foot you will need to increase to 4" pipe.
    708 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  15. How high should my pipe be ?
    When choosing a location for your American Harvest , make sure you meet the minimum clearances listed in the Owners Manual for both the stove and the venting system. We recommend a pellet vent kit ( Dura-Vent or metal Fab are excellent examples), Which includes the necessary clean-out "T", with a four foot vertical run and cap.
    780 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  16. What is the clearance to the back wall ?
    The clearance from the back of unit to the wall is 9".
    780 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  17. How long does it take for the auger and agitator to start turning when I first turn the unit on ?
    They will start rotating after 3 Minutes.
    846 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  18. Why will my Disribution/Circulation fan not run during testing phase ?
    The fan will not operate until a fire is present and the temperature inside the stove reaches 110 degrees.
    698 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  19. Why does my unit shut down after only 15 minutes of testing.
    The stove is not burning and the minimum temperature has not been reached. The thermodisc will begin to shut down the unit.
    605 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  20. How do I reset the control board once the Green light has started flashing ?
    Turn the control board knob completely off and then back on. This will reset the control board.
    720 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  21. When I turn the knob to 1 how long before the unit starts to turn the auger ?
    From the moment you turn the knob to " 1 " the auger and agitator will start to turn in 3 Minutes.
    719 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  22. How far open should my slide draft be set ?
    During start up pull the draft control out about 1/4 inch. ( Note ) depending on the fuel, this may need to be adjusted. After the fire has been established ( usually within 10 minutes ) set the heat setting to " 3 " and adjust the draft slide accordingly.
    645 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  23. How often should I clean out this unit ?
    Everyday this unit should be checked to make sure there is no accumulation of soot behind the back wall slide cleanout. Also make sure that the hole in the top of the firebox is free from soot and ash.
    697 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  24. Fire keeps going out for no reason.
    If the air shutter isn't set correctly it can cause the flame to go out. Make sure the auger has not stopped feeding fuel to the pot. High moisture content in the fuel will cause flame to go out. The sensors on the unit will shut it down if it gets too hot.
    700 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  25. What are the slides in the back wall at the bottom for ?
    They are clean-outs for the ash build up behind the wall.
    751 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  26. What are the slides in the bottom of the firebox on each side of the burn pot for ?
    These are ash clean outs.
    773 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  27. My fire burns with a lazy Orange Flame, what causes this ?
    It could be from the following: moisture too high in fuel, blockage of combustion air, glass door not shut or too loose, draft control knob set too low, feed rate for fuel is too high, inadequate combustion air, clean out plates missing or not fully closed.
    678 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  28. Where does my unit pull in air from ?
    The air inlet for combustion comes from underneath by the ash pan.
    756 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  29. My stove will not shut down properly no matter what I do, I have to unplug it to shutdown. Any suggestions?
    This unit has a saftey heat sensor and will shut down when the firebox is below 90 degrees. Pull out the draft slide on the left hand side of the unit. This will cause the unit to open its exhaust flow completely allowing the unit to blow all the heat out making it shut down sooner.
    684 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  30. I have a model 6037, and the auger doesn't work all the time.
    If the stove senses a vacuum leak (air), it will not operate properly. Make sure the door is sealing tightly. Also, check the pressure switch and vacuum hose. Make sure the ash slides are closed tightly during operation.
    532 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful


  31. I have a 6037 stove, the glass gets completely covered with soot within an hour of running, and I can't keep the stove running on settings #1 and #2, I burn good Iowa corn, 14%. My father-in-law doesn't have these problems with his 6035. Can I adjust the damper with the 6037 to keep my glass cleaner? Do you have a field technician in Iowa, I would like to have him look at my 6037, to be honest I wasn't too happy with in last year.
    Ok, we suggest a moisture content of about 11%, so where 14% is good the dryer is better. You may try adding some pellets to absorb some of the moisture. A moist corn will cause alot of ash and soot if too moist. Once you get your fire started like 10 mins, turn up to 3 setting adjust the manual damper on the side of your stove where the control board is pull it out about 1/8 inch, do not let the fuel builup past 11/2 in the burn pot, if over this it could cause your stove to burn dirty, if too low in the firepot it will go out. No two stoves are going to burn the same. Homes are differnt and a lot of factors also play factors in the operation of a unit. Hope this helps
    522 visitor(s) thought this was helpful. Do you? Yes, it was helpful No, it was not helpful




Get your own FREE Faq today! 
Report Content ·  · Counters & Site Stats   Online Photo Albums   Free Guestbooks   Cheap Domains 
powered by Powered by Bravenet bravenet.com